If you are a cat, you know, if you give them something from scratch and sleep sofas in which you end up with claw and cat hair on the furniture. Create a cat tree and solves these problems much more. Building a cat tree is a pleasant and meaningful project that animal lovers can choose all, too. Cat Cats seem to love trees - they send you a gift, have fun while helping.
To create a scratching post with 4 catsPerching areas are the necessary materials.
Materials
Cat perches -22 "length of 12 cm are tubes of diameter, length 3 is cut, folded sections
Scratching Posts-measurement branches 4-5 inches in diameter, with bark intact. You need 3 branches paired and each pair should measure 4 feet 6 inches, 2 feet 9 inches and 9 inches
Cat Supports tree takes three branches 19 cm long, 2 cmIn diameter, the bracket of contributions under the cat perches. 2 additional branches about 13 cm in diameter and 2 inches to anchor the support of the Persian cat.
Shelf Perch 19 "x13" plywood to stabilize for use in goal.
Base -2 'x 2' sections of 3 / 4 "plywood. Plywood Two sections of disc springs are 12 and have had hardware (4.1" x 3-1/2 "), anchor bolts, and at least 20 or 24 (1 "-1 / 2") wood screws. cloth and cotton-4Cloth squares measure 26 "square of cloth and a 34" material and durable cotton.
Several wood-glue or carpenter, and about 3 cm long nails
Tools-hammer, drill, screwdriver, stapler, staples standards, some wood clamps, measuring tape and pencil markings.
Step by step instructions to build your cat tree
Assembly for review:
1. Practice to consider a couple of holes in the bottom of the branches for the posts.
2.Connect the branch supports between the upper sections of two posts with some nails.
Assembly for the base:
1. Create a base of 2 sheets of plywood to be attached together with wood glue.
2. Allow 24 hours for the wood glue to dry and then drill three holes on two opposite sides of the base. The holes should be about 2 cm from the edge of plywood shown.
3. Mark the areas in which attach to the branch Posts by drawing a circle 1 inch isfrom the edge of the plywood. It should be the same size as one end of the post offices. Repeat the pattern in each of the 4 corners and add a circle halfway between the two corners.
4. With a pencil mark where to drill holes in each circle.
5. Sinks with a "1 drill will make sure that the hardware in detail far enough into the woods, not damage floors.
6. top cover of the base with the "34 square cloth and stapleMaterial under the plywood.
Post and Base Installation Instructions:
1. Use the 3-1/2 "lag screws to secure the contributions and soil. With a screw and washer, attach the 9" in front after mounting the base. Bring the 2'-9 "post assembly in the middle, and 4'-6" post mounted on the back. This creates a ramp for your cats.
2. Leave the screws slightly loose.
Implementation of the plan to support the cat tree perch:
1. Put the cat in a treevertical position. Disconnect the 13-branch between each pair of high-level and all contributions.
2. Next, you must attach the post 13 x19 "plywood cat perched on the shelf so that it does not wobble.
3. Remove immediately put the shelf up in support of standing wood screws 2 inches before the parentheses.
4. supported with 3 screws per side for the shelf to put the perches 2 inches ..
5. You can now drag down the restScrew ..
Bring remaining perches:
1. Cut the 12 "tube diameter longitudinal curved in three sections, each 22" long.
2. Place a portion on each of the following meeting. Use 2 screws to secure the lines are to each post.
3. Cover the curved section with a permanent bar and a 24 "cloth removed. Perches Use parentheses to fix the fabric to the underside of the lid des shelf cat perched in the same way.
Now you have successfullybuild your own place to scratch. The use of branches with the bark still attached is environmentally friendly, and you move from having to use expensive wood and sisal rope to hold.
matchfinalworldcup2010 gamespopcap weddingdresses2010
Continuar leyendo
Ocultar articulo